KEY: Jaguar Paint Color Codes are located at position 8.
1
Front supportAll Modelspassenger side
2
Radiator supportAll Modelscenter
3
Front supportAll Modelsdriver side
4
Wheel housingAll Modelspassenger side
5
Wheel housingAll Modelsdriver side
6
Firewall
7
Door pillarAll Modelsdriver side
8
Door jambAll Modelsdriver side
9
Door jambAll Modelspassenger side
10
Deck lidAll Modelspassenger side
11
Deck lidAll Modelsdriver side
12
Inner Rear Compartment
13
Strut TowerAll Modelsdriver side
14
Hood underside
15
Driver door panel pocket
16
Glove Box
Jaguar Paint Charts and Color Codes for 1981
SAMPLE
COLOUR
MFG. PAINT CODE
YEAR
Jaguar Damson Red
BLVC-211
1981
Jaguar Tudor White
BLVC-215
1981
Jaguar Racing Green Poly
BLVC-281
1981
Jaguar Cobalt Blue Poly
BLVC-286
1981
Jaguar Sebring Red
BLVC-287
1981
Jaguar Chestnut Brown Poly
BLVC-292
1981
Jaguar Grosvenor Brown
BLVC-298
1981
Jaguar Portland Beige
BLVC-299
1981
Jaguar Rhodium Silver Poly
BLVC-396
1981
1981 JAGUAR IMPORTED CAR COLORS
MFG. PAINT CODE
COLOR
COLOR NO.
YEAR
211, CDG
Damson Red
22649
1979-1981
215, NDC, NCF
Tudor White
22652
1979-1981
281, HDN, HAF
Racing Green Poly
22654
1979-1981
286, JDM
Cobalt Blue Poly
22650
1979-1981
287, CDJ, CDE
Sebring Red
22655
1979-1981
292, BDA
Chestnut Brown Poly
22657
1979-1981
298, AEB
Grosvenor Brown
22928
1981
299, AEA
Portland Beige
22929
1981
311
Mineral Blue Poly
22991
1981
373
Black
396, MDE, MCB
Rhodium Silver Poly
22931
1981
NAPA Martin Senour Paints
Acrylic Enamel Basecoat/Clearcoat System
Designed to repair O.E.M. basecoat/clearcoat finishes applied by the vehicle manufacturer. This system provides a finish that exhibits a beautiful wet gloss with improved durability. The development of the basecoat/clearcoat system is a significant breakthrough in Automotive Clearcoat Refinishing virtually eliminating the problems normally associated with a clear top coat finish.
Preparation: Wash the area to be refinished with detergent and water. Solvent clean with No. 6383 Kleanz-Easy. Dry sand with random orbit sander using 240 Lube-Kut Paper. Treat exposed steel with No. 6877 Triple Etch. Treat exposed aluminum with No. 6879 Twin Etch and No. 8829 Zincrom Primer. For spot surfacing use Martin-Senour Lacquer Primer Surfacers Nos. 3252, 3253, 3257 or 3258. For complete surfacing use No. 8094 Synthol Enamel Primer Surfacer. Seal with Quik-Seal non-sanding primer sealer Nos. 8097, 8098 or 8099 reduced 100% with No. 8004 Symmetro Flow Reducer. Allow to dry a minimum of 30 minutes before recoating.
Basecoat Application: Reduce the Acrylic Enamel Basecoat 75% with no. 8831, 8832 or 8834 Acrylic Enamel Reducer. Add No. 8850 Catyl-Ad to the reduced basecoat in the proportion of 4 oz. of No. 8850 to one quart of unreduced basecoat. The sprayable pot life, at 75�F. is six hours. Apply two to three light coats at 50-60 p.s.i. at the gun, allowing a minimum of 20 minutes flash time between coats. (This is less than the film thickness required for regular Acrylic Enamel). Apply only enough basecoat to achieve hiding and color uniformity. The basecoat does not need to be glossy. Maximum film thickness of basecoat is 2 mils. Drying time before clear is two (2) hours above 70�F., and sixteen (16) hours below 70�F.
Clearcoat Application: No. 8852 Clear is supplied ready to spray. Add No. 8850 Catyl-Ad in the proportion of 2 oz. of No. 8850 to 1 quart of No. 8852 Clear. If more flow is desired in the Clear, reduce the mixture up to 25% with No. 8831 or 8832 Acrylic Enamel Reducer. Apply two medium wet cross coats at 45 to 55 p.s.i., allowing a minimum of 15 minutes flash time between coats. Do not add excessive amounts of Clear. Allow to dry overnight at temperatures no cooler than 65�F. The maximum film thickness of Clearcoat that may be safely applied is 1.5 mils.
SPECIAL NOTES:
Fisheyes: Do not use regular No. 77 or No. 77B Squirtz in Basecoat and Clearcoat. If Fisheye presents a problem, add 2 to 4 ounces of No. 87 Fisheye Eliminator to unreduced gallon of both Basecoat and Clearcoat.
Catyl-Ad #8850: Must be added to the Basecoat and Clearcoat or a film failure will occur.
Force Drying: The basecoat may be force dried for 15 minutes at 120 to 125�F., prior to applying the Clearcoat. Do not force dry after the Clearcoat has been applied.
Note:
It is important all products and procedures specified in this systemf must be followed. Any usage of the Basecoat/ Clearcoat system other than stated above or on the product label is at the customer's own risk.