1981 Ford Europe Paint Charts and Color Codes

Send This Page To A Friend
Fade To White
1981 Ford Europe Paint Charts and Color Codes


For correct identification, please refer to the colour code listings on this site.
Paint Code Location Chart
1

Front support-passenger side

2

Radiator support-center

3

Front support-driver side

4

Wheel housing-passenger side

5

Wheel housing-driver side

6

Firewall

7

Door pillar-driver side

8

Door jamb-driver side

9

Door jamb-passenger side

10

Deck lid-passenger side

11

Deck lid-driver side

12

Inner Rear Compartment

13

Strut Tower-driver side

14

Hood underside

15

Driver door panel pocket

16

Glove Box

Fiesta Paint Charts and Color Codes for 1981
SAMPLE

COLOUR

MFG. PAINT CODE

YEAR

1981 Fiesta Forest Green Poly

Fiesta Forest Green Poly

40

1981

1981 Fiesta Crystal Green Poly

Fiesta Crystal Green Poly

60

1981

1981 Fiesta Arctic Blue Poly

Fiesta Arctic Blue Poly

70

1981

1981 Fiesta Diamond White

Fiesta Diamond White

B0

1981

1981 Fiesta Dove Gray

Fiesta Dove Gray

C1

1981

1981 Fiesta Terra Cotta

Fiesta Terra Cotta

D0

1981

1981 Fiesta Gold Poly

Fiesta Gold Poly

H0

1981

1981 Fiesta Prairie Yellow 2

Fiesta Prairie Yellow

K0

1981

1981 Fiesta Sunburst Red

Fiesta Sunburst Red

P1

1981

1981 Fiesta Aztec Bronze Poly

Fiesta Aztec Bronze Poly

S1

1981

1981 Fiesta Light Blue

Fiesta Light Blue

T0

1981

1981 Fiesta Strato Silver Poly

Fiesta Strato Silver Poly

V0

1981

1981 Fiesta Midnight Blue

Fiesta Midnight Blue

X0

1981

1981 FIESTA IMPORTED CAR COLORS
MFG. PAINT CODE
COLOR
COLOR NO.
YEAR
40
Forest Green Poly
22896
1980-1981
60
Crystal Green Poly
22898
1980-1981
70
Arctic Blue Poly
22899
1980-1981
B0
Diamond White
22140
1978-1980-1981
C1
Dove Gray
22893
1980-1981
D0
Terra Cotta
22715
1980-1981
H0
Gold Poly
22710
1980-1981
K0
Prairie Yellow
22894
1980-1981
P1
Sunburst Red
22895
1980-1981
S1
Aztec Bronze Poly
22897
1980-1981
T0
Light Blue
22714
1980-1981
V0
Strato Silver Poly
22347
1978-1980-1981
X0
Midnight Blue
22557
1978-1980-1981

NAPA Martin Senour Paints


Acrylic Enamel Basecoat/Clearcoat System


Designed to repair O.E.M. basecoat/clearcoat finishes applied by the vehicle manufacturer. This system provides a finish that exhibits a beautiful wet gloss with improved durability. The development of the basecoat/clearcoat system is a significant breakthrough in Automotive Clearcoat Refinishing virtually eliminating the problems normally associated with a clear top coat finish.

Preparation: Wash the area to be refinished with detergent and water. Solvent clean with No. 6383 Kleanz-Easy. Dry sand with random orbit sander using 240 Lube-Kut Paper. Treat exposed steel with No. 6877 Triple Etch. Treat exposed aluminum with No. 6879 Twin Etch and No. 8829 Zincrom Primer. For spot surfacing use Martin-Senour Lacquer Primer Surfacers Nos. 3252, 3253, 3257 or 3258. For complete surfacing use No. 8094 Synthol Enamel Primer Surfacer. Seal with Quik-Seal non-sanding primer sealer Nos. 8097, 8098 or 8099 reduced 100% with No. 8004 Symmetro Flow Reducer. Allow to dry a minimum of 30 minutes before recoating.

Basecoat Application: Reduce the Acrylic Enamel Basecoat 75% with no. 8831, 8832 or 8834 Acrylic Enamel Reducer. Add No. 8850 Catyl-Ad to the reduced basecoat in the proportion of 4 oz. of No. 8850 to one quart of unreduced basecoat. The sprayable pot life, at 75F. is six hours. Apply two to three light coats at 50-60 p.s.i. at the gun, allowing a minimum of 20 minutes flash time between coats. (This is less than the film thickness required for regular Acrylic Enamel). Apply only enough basecoat to achieve hiding and color uniformity. The basecoat does not need to be glossy. Maximum film thickness of basecoat is 2 mils. Drying time before clear is two (2) hours above 70F., and sixteen (16) hours below 70F.

Clearcoat Application: No. 8852 Clear is supplied ready to spray. Add No. 8850 Catyl-Ad in the proportion of 2 oz. of No. 8850 to 1 quart of No. 8852 Clear. If more flow is desired in the Clear, reduce the mixture up to 25% with No. 8831 or 8832 Acrylic Enamel Reducer. Apply two medium wet cross coats at 45 to 55 p.s.i., allowing a minimum of 15 minutes flash time between coats. Do not add excessive amounts of Clear. Allow to dry overnight at temperatures no cooler than 65F. The maximum film thickness of Clearcoat that may be safely applied is 1.5 mils.

SPECIAL NOTES:


Fisheyes: Do not use regular No. 77 or No. 77B Squirtz in Basecoat and Clearcoat. If Fisheye presents a problem, add 2 to 4 ounces of No. 87 Fisheye Eliminator to unreduced gallon of both Basecoat and Clearcoat.

Catyl-Ad #8850: Must be added to the Basecoat and Clearcoat or a film failure will occur.

Force Drying: The basecoat may be force dried for 15 minutes at 120 to 125F., prior to applying the Clearcoat. Do not force dry after the Clearcoat has been applied.

Note:


It is important all products and procedures specified in this systemf must be followed. Any usage of the Basecoat/ Clearcoat system other than stated above or on the product label is at the customer's own risk.
Latest Classic Car Classifieds


You may also like...